Messana Communication Daemon Release Notes

added spacepak SIM and Hero Plus heat pumps modbus error readings

added spacepak SIM modbus protocol

added Ritter Thermal Plus heat pump modbus protocol

fixed mTouch error visibility when the mTouch is associated to an mSense probe directly connected via serial cable to an expansion

fixed digital input read from mZone expansions

Fixed wrong zero reset of ATU dirty filter delay.

Fixed SetCoil assert for general modbus protocol.

Fixed mTouch error handling.

ATU errors and warnings:for NTD and HiDew ATU, water low temp warning removed in cooling and high temp warning visible only when cooling.

Corrected Spacepak sim modbus protocol for change of season command.

Delayed room sensor comm. error : wait 2 minutes (default) to display the comm. error of a room sensor.

Phnix hero plus modbus communication protocol available.

Throw error when an mTouch is turned off.

Fixed hanging issue for ATU calibration process.

Fixed modulation computation for Phnix Hero Plus heat pump.

Improved readability for calibration logging process.

Inhibit high water temperature error in heating mode for HiDew REx ATU family.

Added support for Amitime heat pump via modbus.

Added support for Phnix Hero Plus heat pump via modbus.

Improved communication protocol for Syxthsense room sensor. The set point is written on the room sensor before it’s read from it.

Discard a non valid value received from a modus master device.

Improved support for Syxthsense room sensor from firmware version 427.

Fixed calibration process for HiDew ATU.

Fixed modbus communication protocol for drs300/450 ATU.

Added function for supply air temperature control on HiDew ATUs.

Added parameters for Maximum Defrost Time and Defrost End Temperature on LuBA ATUs.

Adding writing of "Time ON defrost" parameter for ATU 1200.

Fixing heating/cooling mode and speed setting for HiDew RxE units.

Fixed Celsisus degree initialization.

Timer override reset when timer mode changes.

Improved watchdog on serial thread to avoid daemon termination when multiple device are in communication error.

Saved period for the filter claning reminder in the database.

Add management of ATU LuBa DRS450.

Implemented communication with generic expansion Dixell iPro215D.

Improved of communication with mTouch on management of timers related to the zones.

Improved management of communication error with room sensors on mControls.

Improved of communication with mTouch on management of timers related to the zones.

Unified log file between the daemon and its libraries.

Management of mZone RD/Jaga.

Added Security logic: exclusion from cooling of zones with high dew point level.

Updated Dynamic ΔR logic.

Added timers to zones for fire-pit, towel warmers, electrical radiant floor or generic purpose management.

Added Exhaust Air Extraction function for new ATU series.

Fixed Mitsubishi FCUs activation (via Procon).

Upgrade for compatibility with version of Database library [0.03.00].

Manual management of AO and DO (for support Test I/O page in the configurator) Room sensor: NewtOhm SND-mTH communication via mZones or mBoxes.

Room sensor: NewtOhm SND-mTH communication on ATU bus.

Fixed reading value of RH by some ATU models. HiDew REx units: - Written the temperature setpoint in ºF in the dedicated register. - Removed setting on for "Forced treatment off". Fixed error on HiDew REx activation: renew always on during other function.

Management of multiple serial buses. Communication with units for HRV only (HiDew RxE).

Changed the method (from incremental to random) for keep mZones and mBoxes alive.

Fixed error on missing conversion from ºC to ºF for the H2O temperature in the HiDew RSx units.

Hidden "General alarm" on LuBa’s ATUs when raised together other kind of alarm.

Reduced the size of the messages for mZones and mBoxes actuation with the aim to reduce the number of communication error in devices connected via RS485.

Implemented communication with SenseAir tSense via mZones or mBoxes

Implemented communication with Belimo 22UTH-..50X.

Added “Sleep Mode” for HiDew REx units.

Added parameter for "Probe on board" on HiDew REx units; allow to manage in the right way the “unplug display” error form the unit.

Communication with HiDew FCUs.

Saving of the calibration data for HiDew ATUs.

Fixed the communication with UnderTree outdoor sensor.

Fix error in acquiring notifications from database about information change.

Communication with SyxthSense SRI 75 sensor (via ATU bus).

Setted environment temperature to "No Value" when the display of the HiDew REx is unplugged.

Management of FCUs on the same duct of the ATUs.

Saving of the calibration data for HiDew REx units.

Fixed humidification issue when the humidificator works with HiDew RER unit.

First release! 🚀